Blown Hydraulic Hose on Site: What to Do Before the Van Gets There

A blown hose doesn't have to cost you the day. Make it safe, take three photos, and send them before the van rolls.

Sean Sasges, HD Force MaintenancePublished Updated 4 min read
HD Force hose van and service truck beside a Case backhoe for hydraulic hose repair on site

A blown hydraulic hose is one of the most common reasons a machine stops on a job site. It's also one of the fastest to fix, if the first ten minutes go right. Here's what we tell site supers and operators from YVR to Hope.

1. Stop and make it safe

  • Stop working the machine as soon as you see oil spraying or the function goes dead.
  • Lower the bucket or attachment to the ground so nothing is held up by hydraulic pressure.
  • Shut the engine off. Follow your operator's manual for relieving pressure in the system.
  • Keep people clear of the area until the machine is shut down.

2. Never touch a leak

Never run your hand along a hose to find a leak. A pinhole leak can inject hydraulic oil through the skin. It may look like a small cut, but it is a medical emergency. If it happens, go to the emergency department right away and tell them it's a hydraulic injection injury.

Do not approach or search for a pressurised leak, even with cardboard, gloves or safety glasses. Inspect and photograph the hose only after shutdown and pressure relief, following the operator's manual. Leave leak testing to the mechanic.

3. Contain the oil

Put down absorbent pads or a spill kit if you have one, and keep oil out of ditches and storm drains. Follow your site's spill rules. Don't keep running the machine with a blown hose. Running it low on oil can damage the pump, and that turns a hose job into a much bigger repair.

4. Take three photos

These save the most time:

  1. The whole hose, from end to end if you can see it, so we can see where it runs.
  2. Both fittings, close up, where the hose connects at each end.
  3. The writing printed on the hose (the layline). It shows the size, the type and the pressure rating.

Also send the machine make and model, and where on the machine the hose is (boom, stick, bucket, track drive, pilot line).

5. Send it and tell us where you are

Text the photos to 778-789-0035, with the site address or a map pin. That lets us check that the van is carrying the right hose and fittings before it leaves.

What happens when the van gets there

Our hose van carries a wide range of hose sizes and fittings. The mechanic removes the damaged hose, builds the new one at the machine, installs it, tops up the hydraulic oil and tests the function. Hose and fittings come from our partner GreenLine Hose & Fittings. If we can't match an unusual fitting on the spot, we source it and come back to finish the job.

During regular hours (Monday to Saturday, 6:30 a.m. to 7 p.m.) the hose van aims to be on site within 2 to 3 hours. Hose repair is $120/hr plus parts and travel, based on a 12-hour work day. If you need us past 12 hours, we'll ask you first, and the extended-hours rate applies. Otherwise we'll be back tomorrow.

How to stop the next one

Most blown hoses we replace didn't fail without warning. Look for:

  • Rubbing. Hoses that rub on steel or on each other wear through the cover. Check clamps and guards.
  • Cracked or weathered covers on older hoses, especially ones that sit in the sun.
  • Damp, oily fittings. A fitting that's always wet is getting ready to fail.
  • Kinks and tight bends where a hose flexes every time the boom moves.

Catching these during preventative maintenance is cheaper than a breakdown in the middle of a pour.

Related service

Mobile Hydraulic Hose Repair

Related articles

Hose blown right now? Call or text a photo to 778-789-0035.

Call now
778-789-0035
Text us a photo